| $$ ADC Oil Filter Systems | We have two filter kits that are applicable to the C24 and other Beech aircraft--the ADC Oil Filter System, and the ADC Remote Spin-on Kit. Both are STC/PMA'd for your engine and aircraft. The ADC Filter System ($675) takes longer to install because you have to wire the bypass light to the panel. The average installation time is about three hours, and shouldn't take much longer than this. Wiring the optional chip detector ($22  may add 30 minutes. The ADC Spin-on Kit ($475) takes about two hours to install, unless you purchase the optional chip detector ($22 , which once again must be wired to the panel. In this case you are looking at approx. 2 1/2 - 3 hours total. We don't usually offer club discounts because we haven't seen benefits to do so, but since you're asking, we are willing to do so on a trial-basis for a limited period of time (say approx. three-six months). We will offer a $50 discount off of the ADC Oil Filter System, and $40 off the Remote Spin-on Kit. If this discount shows an increase in sales, we'll be willing to continue it indefinitely. Also, please let your fellow members know to call in their order rather than order on-line. It's more efficient, and also we can process the discount this way. Regards, Gordon Breuer ADC 800-944-3011 206-546-3011 Fax: 206-546-8035 |
| $$ Aero Fairings Of Canada | This is a Canadian manufacturer of non-approved replacement external fairings, made of fiberglass using Vinylester resin (a very good type that is also used in the Express and Glasair, as two examples). I am pursuing some additional information. They will offer BAC members a 20% discount off their list prices. Note that their website photo seems to show a one-piece tailcone, but the one they sell is actually a two-piece unit. The parts are made to order from their large mold inventory, but lead times are pretty short. Unfortunately, the parts do not include any FAA-approved paperwork. If you wish to install them, your A&P-IA will have to apply for a Form 337 Field Approval, and the manufacturer may have to furnish "approved data" in order to get the field approval. If one of our members accomplishes this, a copy of that 337 will certainly help support future field approval requests from others. Aero Fairings has no plans to pursue an FAA-PMA certification, nor STCs, because in Canada there is a workaround that owners can use to install the fairings without paperwork. Their prices, when converted to USD, are very attractive. For example, wingtips run $345 CD, which converts to about $235 USD; as opposed to the price of $300 USD at Globe Aero. The following is the message BAC received from Aero Fairings. "We can supply most of the exterior fairings installed on the BAC club members' single engine Beechcrafts. Please refer to the Beech section of our web site: www.aerofairings.ca" Claude Buisson |
| $$ Aircraft Engravers | Aircraft Engravers produces custom panel overlays of many different styles, colors, and materials. Their custom overlays can make aged or modified panels look like new. They also make radio faceplate overlays that can make many older radios (such as the King KX170 series) look like new. In addition to the overlay services, AE is also capable of providing custom engraving on items such as your fuel filler caps. For example, you can have your N-number, fuel grade and capacity, and useable fuel engraved on your filler caps. This meets the placarding requirements of the A1CE Type Certificate, so you no longer have to deal with replacing the damaged filler neck decals. Wayne at AE will give a BAC member discount of 10% on single orders. If a group of members merge their efforts and order four to seven pieces, with a single invoice and shipping address, the discount rises to 15%. I have installed their engraved caps on a Glasair I built, and have used their radio faceplate and panel overlays on two different planes. Thoughtful design and placement of a new overlay can make an old panel look almost like new, as (for example) it can hide unused or mismatched holes, and can conceal scratched paint. |
| $$ Arrell Aircraft - Beech Parts | ARRELL AIRCRAFT SALES, INC., a surplus supplier of GENUINE Beechcraft parts, for ALL models of Beech Aircraft, from the Musketeer, to the 1900 Airliner. We have been in this business since 1969, and have extensive knowledge in replacement parts for this line, at VERY affordable prices, as well as on-shelf delivery, for more than 35,000 line items. Our only interest is providing the right part, at the right price, to keep these great aircraft flying. For more information: Rick Leatherwood, Pres. Arrell Aircraft Sales, Inc. 701 Del Norte Blvd., Ste. 220 Oxnard, CA 93030 (805)604-0439 fax (805)604-0429 E-MAIL: BeechedOut@aol.com NOTE: Arrell Aircraft tries to give us at least 5% off RAPID prices on Beech parts. They can sometimes do better on consignment parts. |
| $$ Aviation Engineering Consultants | AEC is a specialty parts manufacturer that seeks to produce hard-to-find and/or overpriced parts, under a primary Parts Manufacturing Authority (PMA). A PMA allows a replacement part to be installed with a maintenance log entry only (no 337 required). AEC is currently producing landing gear cushions (donuts), and is examining some sample H2532-13 exterior door handles, for the Aero Center aircraft. The alternative FAA-PMA gear cushions (donuts) are now available from AEC. Kamran hopes and expects that the automated website ordering will be working on Monday; AEC My understanding is that the online ordering capability is now live, and includes a credit card option. Note that if the new online ordering capability does not work at the time you try it/need it, Kamran can accept manual orders by phone, but they will require non-card payment methods. Evidently AEC isn't set up for card orders in their office. Below is the parts list and AEC pricing; I have added the current RAPID pricing in red. The prices do not include shipping cost; you will have your option of preferred shipping to your location. If you are outside the USA, and as a BAC member you have purchased small parts from me before, please contact me offline if ordering from AEC is a problem for you. The magenta commentary is mine, not AEC's. I got HTML bolding to work in this text, but not color, size, nor underscores. The color-coding and bolding probably will not show up in the mail list text either. I will CC Tim Flight, in hopes he can format this News Article on the BAC Home Page for me. If you need a formatted copy before Tim can get to it, send me the request for an email copy. 1 set, AEC-169-380003-7, 8 pieces/set, $360.00/set. (RAPID $674.26) These supersede the 169-380003 basic number part. These fit all three fixed-gear legs, and the nose gear on the Model 24 retracts. Three sets (total of 24 discs) will be needed to do all three gear on the fixed-gear planes, Models 19 and 23, and associated fixed-gear variants) 1 set, AEC-169-380098-1, 8 pieces/set, $520.00/set. (RAPID $1,202.36) These fit the main-gear legs on the Model 24 retracts. Two sets will be needed to do both main gear on the retracts, plus one set of the -7s for the nose gear. Some sources have referred to these as 169-380098-3 or Lord J11968-10 cushions, but those are numbers that are used only on individual cushions; they do not apply to the full sets. Only full sets of eight have been available from RAPID, under the -1 part number) 2 Jo-Bolts needed per landing gear side, standard size NAS1669-6L7, $29.00 each. (RAPID $29.78. The RAPID price on these is actually reasonable, but many owners have been paying local shops as much as $50 for these bolts. While the parts book shows one long bolt, the actual application uses two short bolts, presumably to prevent interference with the cushion stack tube. No Jo-bolts on the nose gear; just the mains. IMPORTANT NOTES: The standard size Jo-bolt uses a hole that measures .375 to .378 inch. Oversize Jo-bolts are NAS1751-6L7, and use a hole that measures .3905 to .3935 inch. Oversize bolts are far more expensive, at $67.06 from RAPID. AEC does not plan to stock the oversize bolts. In addition to the shop manual, Beech SI0465-202 should be used as a reference while planning and carrying out this work. This SI authorizes the drilling and reaming of a second set of holes 1.25" below the original hole. If you are using a competent shop, it may be cost-effective to drill and ream new standard-size holes, since you'd be paying for oversize reaming of worn original holes anyway. If the gear legs are not loose prior to beginning the work, standard-size bolts will probably work fine. Shipping options: UPS-next day, UPS-second day, or UPS-Ground Method of payment for phone orders (manual orders) can be: Cashiers check (preferred because it is quicker) Money order is also acceptable Personal checks needs bank endorsement Company checks are acceptable. Best regards, Kamran Rouhani; Aviation Engineering Consultants, Inc. 2159 McMullen Booth Road, Clearwater, Florida 33759 727-723-1332 Phone http://www.aec-inc.com/ customersupport@aec-inc.com k.rouhani@aec-inc.com SPECIAL COMMENTARY: We have been working with AEC on these parts for roughly three years, in hopes of improving on the ridiculous Beech pricing. AEC received their initial FAA-PMA approval for these in June of 2003, but encountered multiple conformance failures in production batches from their contracted suppliers. After several setbacks and repeated additional investment of many thousands of dollars, we now have long-needed parts at roughly half of the Beech price. Many people have been delaying this maintenance in hopes of being able to save $1,000 or so on the job. Now they can. We have been telling AEC about the repeated parts requests, and pent-up demand for these parts. While I have no financial interest in these parts (nor in AEC), I wish to encourage everyone who needs these cushions to buy them as soon as they can. We need credibility as an organized group, if we hope to partner with AEC and other potential suppliers. On their part, AEC can't embark on additional projects with us if they can't recover their initial R&D investment fairly quickly. We hope to move along with things like the Hartwell handles, plastic quadrant covers, shimmy dampers, control knobs, interior plastic, etc. AEC won't be able to put thousands of dollars into those and similar projects, if they aren't recovering the thousands spent on the gear cushion project. Please place your order as soon as you can. |
| $$ Custom Ducts | If the primary link is broken, try this one: http://web.archive.org/web/20050317022928/www.pivot.net/~kinney/ Custom Ducts produces custom-length ducts, SCAT or SCEET, with bonded collars on each end. This greatly enhances durability on ducts that have to be removed and replaced during maintenance. It also helps prevent inner liner separation on lined ducts. Jonathan Kinney is the owner-operator of this small business. He will provide a 5% discount to BAC members on orders up to $100. Orders over $100 will receive a 10% discount. You will be expected to identify yourself as a BAC member, and provide your member number. Jonathan has the option of contacting a BAC Board officer to confirm that the member number coincides with the name on the charge card being used. THERE IS FINALLY A BETTER WAY! We use the best available silicone ducting and vulcanize two .020 layers (or doublers) of fiberglass reinforced silicone on each end of the ducting. The outer doubler extends 1.5 inches back from the end, and the inner doubler (SCAT only) approximately 1 inch. Both the inner support wire and the outer support string are encased between the doublers, greatly reducing the possibilities of unraveling. Ducts are fabricated to the nearest 1/2 inch, and priced individually by size and length. Shorter outer doubler lengths are available for special applications. |
| $$ LoPresti Speed Merchants, Hubba Hubba Wheel Covers | Allison Foster at LoPresti has been offering great one-time product discount offers to BAC members. She has now also offered an ongoing 5% discount to BAC members for all LoPresti products. This does not apply to any special bulk-sale offers by Allison that are published on the BAC website. LoPresti Speed Merchants - Check Out All Our Great Products! Our Hubba Hubba Cap fits most 6 inch aircraft wheels. The Generation II Hubba Hubba Cap has an oversize access door with a 1/4 turn fastener for EASY access to the air valve. How many times have your tires been low on pressure but you did not want to remove the hub cap to put air in your tires? The Hubba Hubba Caps will let you keep your wheels and bearings free of dirt and grime. Speed Merchants 800-859-4757 / 772-562-4757 or fax 772-563-0446 Email: Info@SpeedMods.com 2620 Airport North Drive, Vero Beach, Florida, 32960 |
| $$ Met-Co-Aire Fiberglass Wingtips | Metco-Aire has offered to give a 10% discount to BAC members; This is their normal FBO discount. Just provide your member number and request the discount at the time you place your order. Met-Co-Aire is the industry leader in high performance wing tip design, as the purveyors of the immensely popular Hoerner design wing tip. Currently, in addition to the Hoerner drag reduction wing tip, MCA produces the premier direct replacement fiberglass exterior parts available. These parts are much stronger than the plastic factory originals and are guaranteed not to crack. They are fully FAA approved. P.O. BOX 2216 FULLERTON, CALIFORNIA 92837 PHONE (800) 814-2697/(562)802-3306 FAX (714)521-4982 e-mail info@metcoaire.com |
| $$ Vortex Generators - Micro Aerodynamics - 19/23/24 | $50 discount for BAC members, with your member number. Please note that, at some future point, Micro Aero plans to contact BAC for a member aircraft, for the development of systems for the Duchess and Skipper. (800) 677-2370 MICRO Vortex Generators for the Beech 19A, B19, M19A, 23, A23, A23A, A23-19, A23-24, B23, C23, A24, A24R, B24R, C24R are now FAA STC approved and ready for installation on your airplane. This jet age technology provides a reduction in stall speed, improved stabilator authority, reduced landing and takeoff roll. The Micro Vortex Generators are manufactured under our FAA PMA from aircraft grade 6063-T6 aluminum, alodined to a Boeing mil-spec, ready for painting. Here is a follow-up on 07/11/2005 containing an endorsement: Mike, you can see the VG catalog sheet at this address: http://www.microaero.com/CS_PDF/Beec...sketeer_CS.pdf Micro VG Kit for the Beech Musketeer is now FAA STC approved. The STC certification flights were conducted at our headquarters in Anacortes, Washington (just North of Seattle) and STC#SA0115SE covering all Musketeer models. VGs are full span on the wings, on both sides of the vertical stabilizer and on the bottom (BOTTOM) of the stabilator. You get reduced stall speed, reduced landing distance, much better crosswind control, smoother ride in turbulence and a more stable instrument platform. The Musketeer that we used for the STC certification flights is owned by Ron Sellers who flew it for the first time with the Micro VGs installed and sent us the following E: ?I didn?t really notice much of a change enroute home to Troutdale, but when I slowed down to set up for approach and landing --- HOLY COW !!!!!!!!!. The effect of the VGs is amazing. I really felt the difference as soon as I put in the first notch of flaps and I flew the approach 5 kts slower than normal. The plane handled like an airliner, and the landing distance reduction was incredible. Usually I have to come in pretty slow and use a lot of braking to make the second turnoff. Today, I landed slower and use no brakes to slow down, and was at least 200-300 feet short of the turnoff.? ?I?ll keep you posted as I gain more experience. Thanks again for letting me participate in this project. I will do everything I can to get the good word out to other Musketeer owners.? ------ Ron Sellers, Troutdale, Oregon. Editor's note: Ron Sellers is a current BAC member. The Musketeer VG Kit is $1450. If you want us to paint it to match your airplane we need a paint name and number which is in your aircraft records. There is a $100 charge for painting. With your order we need N-number, serial number, shipping address and any credit card or COD. I look forward to shipping you a Micro VG Kit for your Musketeer. Charles at Micro Aero |
| $$ Vortex Generators - Micro Aerodynamics Home Page | $100 discount for BAC members, with your member number. Please note that, at some future point, Micro Aero plans to contact BAC for a member aircraft, for the development of systems for the Duchess and Skipper. Micro vortex generators are small metal blades placed in a spanwise line aft of the leading edge of the wing. They control airflow over the upper surface of the wing by creating vortices that energize the boundary layer. This results in improved performance and control authority at low airspeeds and high angles of attack. Our office and hangar is located at the Anacortes Airport (74S), in Northwest Washington State, about 90 miles north of Seattle. Office Hours: Monday through Friday 9:00 am to 5:00 pm pst. Toll free: 800 677-2370; Local: 360 293-8082; Fax: 360 293-5499 4000 Airport Road, Suite "D", Anacortes, WA 98221 Web: www.microaero.com E-Mail: micro@microaero.com |
| $$ Welcome to Bogert International (Bogi-bars, wheel jacks, and much more) | Thanks to a request from member David Snodgrass, Bogert International has joined the growing list of participating suppliers offering BAC members worthwhile discounts on their products. They will also purchase a BAC membership, as have some other providers, in order to help keep tabs on questions, etc. Here is the current announcement by Kathy Bogert. Please visit the Bogert website and view the broad range of products (tow bars, jacks, jack pads, gear stands, specialty tools, and much more. Bogert also makes FAA-PMA copper battery cable kits to replace OEM aluminum cables. While they do not currently list the 19/23/24 (I believe that all the 76s and 77s are copper), if we demonstrate a member market for replacement cables, we can approach Kathy. While it is in Kathy's text, please make note that the 10% member discount is a year-round discount offer on all their products. Kathy also plans to offer limited-time specials on various products from time to time. For example, she is offering members a ten dollar discount on the $79 Bogi-bar. This offer reflects a % discount on the Bar, and is good through February 02, 2005. Mike, Cloyd and David, We will join BAC before the end of the year. I don't suspect we will be posting much. If we do, it will be in direct response to the subject in the thread. I agree it is a good thing to moderate the forum. Bogert Aviation is able to offer all BAC members in good standing a 10% discount on our entire product line year round, and reserve the right to sweeten the deal occasionally. Sweetened deals will run for a specified time and specified price. These items will typically be linked to the release of a new product, regional/national fly-ins or when we are overwhelmingly overstocked.  Originally you requested a discount on our Bogi-Bar. You've got it! The Bogi-bars are normally $79.00. Let's take $10.00 off any Beech Bogi-Bar until February 2, 2005 for all BAC members. And... remember the 10% is good on anything year round. Orders can be placed on the web at www.bogert-av.com or call us direct at (800) 627-8088. Orders could also be faxed in to (509) 735-2106. Call us direct if you have questions. But remember, we are on the Pacific Coast and usually start answering phones about 8am PST. Email is always welcomed at info@bogert-av.com. Our contact info is Website: www.bogert-av.com A&P, & Inventor: Richard Bogert Sales & Marketing: Cathy Bogert (Richard's sister, not wife) Email: info@bogert-av.com |
| $$ Woodland Aviation - Beech Parts Discounts | Forrest Barton, Woodland Aviation Parts, 800-442-1333, Beech parts contact; ForrestB@WoodlandAviation.com Arrell Aircraft is a great source for parts. If they have them available, 90% of the time they will beat my price, as many of their parts are New Old Stock consignment sales. I have a great working relationship with Rick and Steve at Arrell, and quite often get things from them myself. Most of the time when Arrell has to get a part from RAPID, I am their supplier. RAPID, unfortunately, isn't making life easy on anyone these days; but if you are forced to deal with RAPID, I can match and often do better than RAPID will offer you direct. Another perk I can provide is a working knowledge of the airframe, when it comes to parts issues, versus talking to the order-takers at RAPID. Just to give BAC members some inside info, RAPID will charge you $100 for an AGO fee, in addition to the cost of the part and the Express shipping cost. You can have them do a Flight Critical Expedite, which wont cost you anything but is not as fast as an AOG. Both of these options will get you parts faster than a standard order. Woodland Aviation has been serving aviators throughout the West since 1963. Family-owned and operated since our establishment, we are proud to maintain a reputation of integrity, innovation and excellence. |
| $$ Electronics International, Inc | Electronics International Inc. manufactures nearly 100 product lines for your aviation needs. From engine and temperature instruments to clocks and timers, we may well offer more STC'd, TSO'd, and PMA's instruments than any other manufacturer in the industry. At Electronics International Inc. customer satisfaction is priority one, which includes providing a good price on systems and accessories. EI has over 2000 distributors worldwide that tend to get price competitive with one another. The most recent information is that EI "might" do a "bulk" purchase option with a discount to BAC Members. If you are considering an EI purchase it might be worthwhile to post in the forums to see if anyone else wants to try to put together an acceptable "bulk" purchase. |
| $$ Hammerhead Aeronautical - Chad Moser | Hammerhead Aeronautical provides a full spectrum of aircraft services, and is a Flight Cheetah dealer. This description is targeted at the Flight Cheetah avionics product line. This site provides a good product overview. http://aviationsafety.com/ Hammerhead-BAC pricing for the Cheetah is going to be: 190FL unit $1700.00 210 unit $2700.00 True map software $ 525.00 WX works receiver $ 525.00 WX software $ 175.00 (Sold separately if XM receiver is not needed.) Electronic Attitude $ 700.00 Traffic Alert $1895.00 Traffic Alert cable/software $ 180.00 (Sold separately if the XRX traffic receiver is not needed) 3D mapping upgrade $ 150.00 Installation hardware $ 130.00 Install about 10-15hrs $ 675.00 (Possibly more depending on panel requirements) Quotes do not include removal of old equipment. Chad |
| $$ Stark Avionics | Stark Avionics might have a small staff, but they are big on service. They offer very competitive pricing on avionics, autopilots, new panels, lighting, and any electrical work. They offer an IFR certification for $225 (as of June 2009). If you are in the market for a new panel, be sure to give them a call. They have a computer generated panels with laser cutting that is exact and fits perfect. Along with the panel production, they offer full powder coating services for all your needs. They are offering BAC members 10% off on all labor. Please provide your member number at the start of work. Contact Stark Avionics at: Phone 706-321-1008/Fax 706-324-3770 Owner: John Stark- john@starkavionics.com Manager: Tony Skahan- tony@starkavionics.com http://www.starkavionics.com/ |
| $$ TKM-Michel Electronics - Discounted Radios - MX170/MX12 | NOTE!! This is a false website name being used as a "place-holder"; it is not intended to be a valid website address! TKM does not have a retail website. I have reached an agreement with TKM-Michel, known in the electronics trade as a major manufacturer of test and measuring equipment. TKM makes the MX series of slide-in replacement radios. In our aircraft, the most common application is for the King KX170 series radios, and the Narco MK12 radios. You can view the links for the MX radios on the BAC website, for detailed info. In summary, they are modern digital flip-flop radios, with frequency storage, that can slide into the same tray when the old radio comes out. Now the best news. TKM will sell factory-refurbished radios to BAC members, complete with a one-year factory warranty, for only $1,200. This is hundreds of dollars below the discounted new cost from dealers, and hundreds of dollars below the typical eBay sales price. This offer is subject to availability. Call Kathy at TKM, 480-991-5351, email TKMRadios@aol.com to purchase a radio. Tell her that you are a BAC member, and that Mike Rellihan sent you. TKM provides excellent service. Not only are their repair rates very reasonable (a recent face refurbishment, with new buttons, cost me $80), but Kathy will ship you a free loaner radio for the price of shipping, if you need it during a repair. Their radios are as reliable, if not more reliable, than those they replace. To top it off, my MX170B has better/clearer receive audio than my Garmin GNS430, and I regularly receive comments that it sounds better on transmit as well. Not too shabby. Another BAC member benefit. Hope you are able to take advantage of it! |
| $$ BAC version of Voyager from Seattle Avionics | Special Offer for Beech Aero Club members Interested in a more advanced version of the product? All Beech Aero Club members are eligible for up to 50% off the retail price of the paid-for starter bundles of Voyager. To learn more, call 425.806.0249 or email sales@seattleavionics.com About Voyager The Voyager Flight Software System is a complete software system that makes flying safer and more enjoyable. Preflight, it will check the weather (a complete and legal briefing) and plan a wind-optimized, fuel-price optimized flight. In flight, it puts a tremendous amount of information at your fingertips in a way that's quick and easy to understand. Voyager is a modular system so you can purchase what you need now and upgrade as your needs change (for example, purchase the preflight planning portion now then add the in-flight moving-map module later). Voyager is also available in a completely free version called Voyager FreeFlight that is a powerful pre-flight planner with weather. See the Summer 2008 BAC Talk for a review of the full version 4 system. |
| $$ Hilton Software 10% BAC discount on WingX | WingX is a flight planning, weather briefing and Electronic Flight Bag bundle for smartphones (including Blackberry, iPhone, and Windows Mobile devices). Developer and CFII Hilton Goldstein extends a 10% discount on all WingX programs and database subscriptions, to all Beech Aero Club members. Be sure to include your BAC Member Number when you order. I was an early adopter of this suite, and am now a beta tester for the Blackberry Storm release (which is still a bit buggy, but that's RIM's fault, not Hilton's!) A complete product review is forthcoming. |
| $$ Mike Busch Savvy Owners Seminars | Tom Kinstler has received confirmation that Mike Busch will extend his $50 group discount to BAC members. Spend a total-immersion weekend with well-known aviation writer, teacher, pilot and A&P mechanic Mike Busch, founder of AVweb, longtime tech rep for the Cessna Pilots Association, and an aircraft owner for 35 years. Mike will share his four decades of aviation experience, and teach you how to be a more savvy and empowered in maintaining your aircraft. You'll take away dozens of invaluable tools and techniques that will save you literally thousands of dollars on the maintenance of your aircraft, not to mention hours of downtime and aggravation, year after year. Learn more... |
| $$ Clarity Aloft Headsets $$ | Clarity Aloft is offering BAC members a discount on their revolutionary headsets. From now through May 1st BAC Members can purchase the headsets for $450 (retail is $650). To order, call 612-747-3197 and identify yourself as a BAC member. The Clarity Aloft headsets employ patented Comply Canal Tips, composed of soft visco-elastic foam, the same foam tips used in advanced hearing aids. More than simple earplugs, these foam tips provide full spectrum noise reduction: 35-45dB of attenuation. This advanced technology has been lab tested to prove that visco-elastic passive noise reduction (VPNR) is superior to active noise reduction (ANR), especially in the speech frequencies, precisely where clarity of sound and hearing protection is most needed for aviation communications. Features and benefits:
Special thanks to John Waterman for arranging this discount! |
| $$ Rosen Sunvisor Home Page | Long acknowledged as the "Industry Leader", Rosen sunvisors are installed as factory original equipment on aircraft of every category ranging from the Cessna 172 to the Boeing 777. Rosen has extended a discount offer of $30 off list price, to BAC members. Please refer to their discount sheet in the Downloads section of BAC. Designed by pilots, for pilots, Rosen visors offer unparalleled safety and comfort. Our optically pure lens material offers the pilot these benefits: Unrestricted visibility. Enhanced feature definition in hazy conditions. 99% reduction of damaging ultraviolet light. Both our Monorail and NSA visor designs allow the lens to be positioned anywhere across the windshield or side windows that direct sunlight creates a problem, then stowed out of the way when not needed. Our precision machining standards produce mechanical assemblies that move fluidly, tension firmly and stay in position. With STC\'d visor systems for most certified aircraft flying, and the unequalled quality that goes into every Rosen system, we think you\'ll agree that there is no better sunvisor value on the market. |
| $$ Norris Hibbler - Aircraft And Marine Assurance | Norris Hibbler has been providing discounted insurance rates to BAC members; particularly on the first renewal. All member feedback for this agency has been very positive. "We, the staff of Aircraft & Marine Assurance, will continue to provide nothing less than the outstanding service that you have come to expect from us. Now and in the future, we offer our dedication and loyalties to help our organization grow and prosper." |
| $$ EZflaphandle | LIMITED TIME OFFER BAC members are being offered an "Early Bird" special discount for the brand new EZ Flap manual flap handle extension. Orders placed through November 17th will receive a 10% discount off the $499 retail price (a $50 value) plus free shipping in the lower 48 (an additional $8 to $10 value). The product comes with a 100% money back guarantee - if after trying the product on your own aircraft you're not completely satisfied and agree it makes a significant improvement in safety, convenience, comfort and performance... return the product in new condition for a full refund. EZ Flap is a well-made, FAA approved control extension device that installs onto your existing Beech manual flap handle in about 30 minutes with only two small holes. No disassembly or de-rigging. Photos and additional information at www.ezflaphandle.com 818-634-9762 Whiteman Airport KWHP Los Angeles, CA Contact: Bill Berle |
Random Member Aircraft
|
Menu
Recent Threads
JP's Barbeque Ribs & Chicken, Bolton Field (KTZR) Columbus, OH - May 19, 2012
Thread Starter: AVIATOR_Fly into Bolton Field on Saturday May 19 and join us at JP's Barbeque Ribs and Chicken located on the field. Restaurant opens at 12:00 noon. Arrive by
Last Post By: scottb613 Today, 04:44 PM